SPLASHTRON FAQs

Below are some of the most Frequently Asked Questions about SPLASHTRON®.

If you have additional questions about SPLASHTRON® or any other of our products please feel free to contact us.

  • Can SPLASHTRON be applied to bent pipe?
  • Can SPLASHTRON coatings be repaired?
  • How is it possible to get long, continuous coverage with SPLASHTRON?
  • How is SPLASHTRON applied?
  • How is SPLASHTRON normally used?
  • How long can SPLASHTRON be expected to last in service?
  • How long has SPLASHTRON been used?
  • How much coverage is usually applied?
  • In what thicknesses can SPLASHTRON be applied?
  • Is SPLASHTRON available from anyone other than Mark Tool Co.?
  • What features account for SPLASHTRON’S success as the most widely used elastomer for “splash zone” coating?
  • What is SPLASHTRON ?
  • What is SPLASHTRON made of?
  • What is the largest pipe that can be coated with SPLASHTRON?
  • Where is SPLASHTRON application facilities located?
  • Who uses SPLASHTRON?
  • Why is SPLASHTRON so widely used in J- tube pulls?
  • Why is SPLASHTRON yellow in color?
  • Will marine growth attack SPLASHTRON?
  •  
     
     
    Q: Can SPLASHTRON be applied to bent pipe?
    A: Yes, though there is a price premium for doing so if the pipe is already bent when we receive it. The more common practice, wall thickness permitting, is to “cold bend” the pipe after the SPLASHTRON is applied.
    Back to Top

    Q: Can SPLASHTRON coatings be repaired?
    A: Yes, but if the damage does not expose bare metal, there is no need to repair it. If bare metal is exposed, trim away the lose material, wire brush the metal, and apply a resilient epoxy patch material available from Mark Tool Co.
    Back to Top

    Q: How is it possible to get long, continuous coverage with SPLASHTRON?
    A: A minimum 6” of bare metal is left on each end of a joint to allow room for welding without demanding the coating. For unbroken coverage, a special SPLASHTRON sleeve to the pipe with epoxy.
    Back to Top

    Q: How is SPLASHTRON applied?
    A: The coating is chemically bonded, as opposed to merely mechanically bonded, to the metal surface to be protected. The bond of SPLASHTRON to metal is stronger than the tough yellow elastomer itself.

    Application must be made in Mark Tool Co’s plant for two reasons: (1) So that the environment and production processes can be closely controlled, and (2) Because the optimum curing vehicle is the steam autoclave.

    Back to Top

    Q: How is SPLASHTRON normally used?
    A:
    1. By far the most popular use is the coating of risers (flow liners) where they pass through the harsh environment of the “splash zone”.
    2. Another excellent application is the coating of platform jacket legs and other structural members in the “splash zone”.
    3. Perhaps the fastest growing application for SPLASHTRON is coating the pipeline risers to be pulled through J- tubes (pull tubes) attached to platforms.
    4. Other applications for SPLASHTRON are coating the inside of riser clamps, coating conductors, and making bottom J-tube plugs.

    Back to Top

    Q: How long can SPLASHTRON be expected to last in service?
    A: There have been SPLASHTRON-coated platforms offshore for more than 35 years, and hundreds of risers have been in use that long. Barring physical damage, SPLASHTRON can be expected to last for the life of the platform or pipeline.
    Back to Top

    Q: How long has SPLASHTRON been used?
    A: The first SPLASHTRON – coated test specimen was put offshore in 1961. Commercial production began a couple of years later. There are installations in the Gulf of Mexico that have been in continuous service for more than 20 years.
    Back to Top

    Q: How much coverage is usually applied?
    A: The “splash zone,” varies in size around the world, depending on tides, weather, etc. In the Gulf of Mexico, 25 feet of SPLASHTRON is normally used; 15’ above mean water level, and 10’ below.
    Back to Top

    Q: In what thicknesses can SPLASHTRON be applied?
    A: The most popular coating thickness is ½”, although ¼” is sometimes used because of clearance limitations. Where good thermal insulation is required, 1" or more is used.
    Back to Top

    Q: Is SPLASHTRON available from anyone other than Mark Tool Co.?
    A: No. SPLASHTRON is an exclusive formulation, proven for more than 35 years offshore, and is only available through Mark Tool Co., or its licensed applicators in such places as Japan and California. SPLASHTRON is a trademarked name.
    Back to Top

    Q: What features account for SPLASHTRON’S success as the most widely used elastomer for “splash zone” coating?
    A: Because for its long, trouble-free service life, SPLASHTRON is very economical to use. It completely shields metal surfaces from corrosive attack and erosion; resists degradation from exposure to seawater, sunlight, ozone, and hydrocarbons. Barnacles and other sea life will not feed on it, and it is an excellent insulator. (will not contribute to galvanic corrosion).
    Back to Top

    Q: What is SPLASHTRON ?
    A: A yellow elastomer coating, bonded strongly to steel pipe to be used in the “splash zone” in offshore operations, primarily to protect against corrosion.
    Back to Top

    Q: What is SPLASHTRON made of?
    A: It is a blend of selected Neoprene polymers, fortified with special additives to form a tough, resilient barrier to corrosion, erosion, chemical attack, ultra violet rays and ozone.
    Back to Top

    Q: What is the largest pipe that can be coated with SPLASHTRON?
    A: There is really no upper limit, although for practical purposes (weight, primarily) we normally consider 68” OD and 44 feet in length working limits. We have applied SPLASHTRON to 96” OD caissons.
    Back to Top

    Q: Where is SPLASHTRON application facilities located?
    A: At the present time, SPLASHTRON is applied in Southern Louisiana, California and Japan. These locations serve the Gulf of Mexico and Offshore California well, and are convenient to major ports for access to foreign markets.
    Back to Top

    Q: Who uses SPLASHTRON?
    A: Most of the offshore producers of oil and gas, plus the pipeline transmission companies. The list of customers read like a “Who’s Who” of the petroleum industry: Exxon, Shell, Texaco, Chevron, Conoco, Amoco, Union Oil, Mobil, Kerr- McGee, Columbia Gas Transmission, and so on.
    Back to Top

    Q: Why is SPLASHTRON so widely used in J- tube pulls?
    A: Primarily because it is such an effective corrosion barrier in an application that will literally be hidden from view for many years. Also, since it is such a good electrical insulator, it prevents metal-to-metal contact and current flow between the pipeline and the J- tube.
    Back to Top

    Q: Why is SPLASHTRON yellow in color?
    A: It is yellow for ready visibility; a safety feature offshore. More important, it contains no carbon black, which can make rubber electrically conductive. Therefore, SPLASHTRON is an excellent electrical insulator.
    Back to Top

    Q: Will marine growth attack SPLASHTRON?
    A: While marine growth will build up on SPLASHTRON, it will not adversely affect it because there is nothing in SPLASHTRON that barnacles and other sea life will feed on. Where marine growth is a problem, such as off California, Mark Tool Co. offers BIO-SHEILD, a patented product which is composed of a layer of SPLASHTRON with a cladding of 90-10 copper-nickel bonded permanently to the outside.
    Back to Top

     

       

     

    © Copyright 2017, Mark Tool Co, Inc.. All rights reserved.